Multistop Blocking Primer
Blocking primer for the prevention of discoloration on interior wooden surfaces.
Blocking primer for interior timber surfaces which prevents resin,
tannin and knot staining.
Ceiling and wall
panels, wooden floors, skirting, doors, windows and furniture.
Suitable as primer and intermediate coat for both untreated and previously painted or varnished (with the exception of certain parquet lacquers), new or old wood surfaces in dry interior premises. Prevents discoloring wood extracts and other yellowing substances such as tar, etc. from entering into the top coat. Prevents discoloration caused by wood knots.
7 m2/l (minimum amount to be applied 260 g/m², wet film thickness 200 µm, dry film thickness 75 µm).
1 l, 3 l and 10 l
Brush, roller or
Airless spray nozzle
0.013", no thinning
Drying time at 23°C and 50% relative air humidity
Touch-dry after approx.
Recoatable with sealing primer after three hours at the earliest.
Recoatable with finishing
paint after approx. six hours.
1.3 kg/l, ISO 2811
Protect from frost.
The surface to be painted must be dry, the temperature at least +10°C, and the relative humidity of the air less than 80 %. A low temperature (approx. +15°C) and higher humidity (50–70 % RH) will extend the working time and make application easier.
In order to ensure the best possible adhesion, clean new wooden surfaces from any dirt and dust.
Wash previously painted or lacquered surfaces with Maalipesu Cleaning agent according to the instructions on the label. Allow to dry. Remove loose paint or lacquer and sand the whole surface – especially floors and furniture. Remove sanding dust. If necessary, use Presto Rapid Filler to fill any cracks and dents, and sand the filled areas. Remove sanding dust. Patch paint with primer on bare wood surfaces.
Note! The adhesion of Multistop to certain parquet lacquers is poor, therefore the parquet lacquer should be completely removed, if Multistop is used over the entire surface.
Multistop well before use. The product is used without thinning. Apply plenty
of the paint, preferably with a thick nap roller and finish the surface once or
twice with a synthetic brush. The best insulation result is achieved when the
treatment is performed twice.
panel ceilings with Paneelikatto Panel Ceiling White, panel walls with a suitable
Helmi Furniture Paint and floors with Betolux Akva. The sealing primer can also
be left on ceiling surfaces without a topcoat as long as the surface is treated
Cleaning of tools
Remove any excess paint from tools. Wash the tools with water. Tikkurila Pensselipesu (Tool Cleaner) is recommended for removing slightly hardened paint.
After the surface treatment, surfaces must be handled with care for a few weeks, as the product will reach its final hardness and durability under normal conditions after about a month.
About a month after painting at the earliest, if necessary, clean the surface using neutral (pH 6–8) dishwashing liquid solution and a soft brush, sponge or cloth. Clean soiled surfaces using mild alkaline (pH 8–10) detergent solution and a cloth, mop or sponge, for example. Rinse the surface carefully.
EU VOC 2004/42/EC-limit value
(cat A/a) 30g/l(2010)
Multistop contains VOC max. 30 g/l
(cat A/g) 30g/l(2010)
Multistop contains VOC max. 30 g/l
HEALTH AND SAFETY LABELLING
according to Regulation (EC) No. 1272/2008
Contains 2,4,7,9-tetramethyldec-5-yne-4,7-diol and reaction mass of: 5-chloro-2-methyl-4-isothiazolin-3-one [EC no. 247-500-7] and 2-methyl-2H-isothiazol-3-one [EC no. 220-239-6] (3:1). May produce an allergic reaction. Wear protective gloves. MULTISTOP
ENVIRONMENTAL and WASTE DISPOSAL
Recycle empty, dry cans or dispose them of in accordance with local regulations. Destroy liquid waste according to the local regulations for hazardous waste.
ser120417 / mkv111115 / akk100915